• 五金加工需要怎么操作?
  • 本站编辑:杭州丰达通信器材198彩票注册发布日期:2018-06-28 15:24 浏览次数:
五金加工01
 
五金加工操作需要注意的细节
Details to be paid attention to in hardware processing operations
1、所有员工在进入工作岗位前,检查自己服饰是否符合工作要求。不准穿拖鞋、高跟鞋及影响安全的服装,留长头发的要戴安全帽。工作时保持正确的姿势,要有充足的精神应付工作,如发现身体不适就要马上离开工作岗位,并向优先导反映。操作时必须思想集中,严禁闲谈,相互配合,操作者切勿在烦躁、疲倦的状态下操作,以免发生事故,确保操作安全。
1. All employees check whether their clothes are up to the job requirements before entering the workplace. No slippers, high heels and safety clothing are allowed. Wear safety helmets for long hair. Maintain correct posture at work, and have sufficient mental energy to cope with work. If you find physical discomfort, you should leave your job immediately and reflect it to your leader. Operation must be concentrated, no idle talk, cooperate with each other, the operator do not operate under the condition of irritability and weariness, so as to avoid accidents and ensure the safety of operation.
2、机械工作前检查运动部分是否加注了润滑油,然后启动并检查离合器、制动器是否正常,并将机床空运转1-3分钟,机械有故障时严禁操作。
2, before the machine work to check whether the movement part of the injection of lubricating oil, and then start and check the clutch, brake is normal, and airlift the machine tool for 1-3 minutes, mechanical failure when the machine is strictly prohibited.
3、更换模具时首先关闭电源,冲床运动部门停止运转后,方可开始安装、调试模具。安装调整完毕后,用手搬动飞轮试冲两次,检查上下模具是否对称、合理,螺丝是否坚固,压边圈是否在合理的位置上。
3, when changing the mold, first turn off the power supply, and after the motion Department of the punch press stops running, the mold can be installed and debugged. After the installation of the adjustment, use the hand to move the flywheel two times, check whether the upper and lower dies are symmetrical, reasonable, the screw is strong, the edge ring is in a reasonable position.
4、必须等其他人员全部离开机械工作区,并拿走工作台上的杂物后,方可启动电源开动机械。
4, we must wait until all the other personnel leave the machine area and remove the debris on the worktable before starting the power supply and starting the machine.
5、机械开动后,由一人运料及机械操作,其他人不得按动电建或脚踩脚踏开关板,更不能将手放入机械工作区或用手触动机械的运动部分。机械工作时,禁止将手伸入滑块工作区,严禁用手取、放工件。在冲模内取、放工件时必须使用符合标准的工具。如发现机械有异常声音或机器失灵,应立即关闭电源开关进行检查。
5. After the mechanical operation, the other people are not able to press the electric construction or foot stepping switch board, and the others can not put their hands into the mechanical work area or touch the mechanical part of the machine. When working in machinery, it is forbidden to extend the hand into the work area of the slide block. Standard tools must be used when taking and placing work pieces in stamping dies. If there is abnormal sound or machine failure, turn off the power switch immediately.
6、下班时,应关闲电源,并整理好岗位上的成品、边料和杂物等,确保工作环境清洁及安全。
6, when you leave work, you should turn off the idle power supply, and finish the finished products, materials and sundries on the job to ensure that the working environment is clean and safe.
33彩票 17彩票 166彩票 大信彩票投注 166彩票 2m彩票官网 江苏快3平台 33彩票 258彩票 江苏快3平台